产品推荐:气相|液相|光谱|质谱|电化学|元素分析|水分测定仪|样品前处理|试验机|培养箱


化工仪器网>技术中心>解决方案>正文

欢迎联系我

有什么可以帮您? 在线咨询

紫外灯用于微针制备的固化

来源:上海路阳仪器有限公司   2025年02月11日 14:36  

近日,天津医科大学与天津大学在《Nature Communications 》( IF 14.7 )期刊发表文献《Microorganism microneedle micro-engine depth drug delivery》,文献中的实验使用了路阳仪器上海公司生产的LUYOR-3109台式高强度紫外线灯,实验采用了LUYOR-3109 365nm台式大功率紫外线灯用于微针制作过程中的固化。

LUYOR-3109 365nm紫外光源安装了27w 大功率365nm led,通过二次光学透镜进行聚焦,紫外光强度超过了传统400w高压汞灯的辐照强度,上市以来,LUYOR-3109已经广泛用于科研院所的科学实验室的紫外辐照,目前,使用LUYOR-3109发表的文献近百篇。如果您实验需要一台大功率、高强度365nm紫外光源路阳仪器上海公司提供样机免费试用

文献摘要:

作为一种透皮给药方法,微针具有微创、无痛和精确的原位治疗。然而,目前的微针依赖于被动扩散,导致药物渗透不可控。为了克服这个问题,我们开发了一种气动微针贴剂,它使用活的产气肠杆菌作为微引擎来主动控制药物输送。这些微生物产生气体,将药物驱使进入更深的组织,可调节的葡萄糖浓度可以精确控制该过程。我们的结果表明,这种微生物驱动的系统将药物输送深度增加了 200% 以上,达到皮肤以下 1000 μm。在银屑病动物模型中,该技术有效地将骨化三醇输送到皮下组织,从而快速缓解症状。这项创新解决了传统微针的 局限性,提高了药物效率、透皮渗透性,并引入了按需受控药物输送的创造性范式。

image.png

Preparation method of single-layer bacteria-carrying microneedles

First, a solution was prepared by mixing PEGDA and anhydrous ethanol in a 7:3 ratio to make a 10 mL solution. Then, 100 µL of HMPP (1%, v/v) was added to the solution, and it was thoroughly mixed to obtain the substrate solution. Next, a solution of Enterobacter Aerogenes ATCC 13048(E.A.) was placed in a centrifuge tube, and the centrifuge was set to 3000 rpm for 15 min. The resulting centrifuged pellet was thoroughly mixed with the substrate solution to obtain a bacteria-loaded substrate material. Different proportions of glucose solution can be added to the substrate solution as needed to obtain microneedle patches with varying substrate concentrations. Subsequently, a microneedle fabrication mold (microneedle width 200 µm, needle length 500 µm) was taken, and 300 µL of the bacteria-loaded substrate material was added to it. The mold was placed in a vacuum pump for 20 seconds to remove any bubbles from the microneedle mold’s needle array. The mold was then removed, and if necessary, it was exposed to a UV lamp(LUYOR-3109, 27w LED lamp) for 5 s to cure, resulting in complete microneedles. If there was any remaining liquid not drawn into the mold’s pores, an additional 300 µL of the substrate solution was added to fill the mold. A UV lamp was used to cure it for 5 s, and the microneedles were demolded to prepare complete bacteria-loaded microneedles.

image.png

文中使用的设备,另外配置多种不同款式紫外灯,中高强度,强度自由调节,物美价廉


免责声明

  • 凡本网注明“来源:化工仪器网”的所有作品,均为浙江兴旺宝明通网络有限公司-化工仪器网合法拥有版权或有权使用的作品,未经本网授权不得转载、摘编或利用其它方式使用上述作品。已经本网授权使用作品的,应在授权范围内使用,并注明“来源:化工仪器网”。违反上述声明者,本网将追究其相关法律责任。
  • 本网转载并注明自其他来源(非化工仪器网)的作品,目的在于传递更多信息,并不代表本网赞同其观点和对其真实性负责,不承担此类作品侵权行为的直接责任及连带责任。其他媒体、网站或个人从本网转载时,必须保留本网注明的作品第一来源,并自负版权等法律责任。
  • 如涉及作品内容、版权等问题,请在作品发表之日起一周内与本网联系,否则视为放弃相关权利。
企业未开通此功能
详询客服 : 0571-87858618