122-39（SD）注射器用导热环氧模贴胶

122-39(SD)注射器用导热环氧模贴胶

说明：122-39（SD）是一种注射器，可有可无，导热，电绝缘，单组分，

100%固体环氧粘合剂。该系统具有优异的热稳定性、优异的耐化学性和

优异的高温性能。应用包括与镀金基板和锡/铅焊料的粘合

端接元件、模具连接和热管理操作、印刷电路板制造、高级

材料复合，密封和高性能涂层。122-39（SD）是122的导热型-

38（标准差）。

属性：

粘度（cps）40000

触变指数>2.5

填料氮化铝

填料百分比60

大体积电阻率（Ω-cm）1 x 1016

热导率（w/mk）3.5

介电常数（1kHz）4.1

介电常数（1MHz）3.9

损耗因子（1kHz）0.027

损耗因子（1MHz）0.038

有效温度范围（℃）-55至+250

热稳定性（℃）良好至+300

模具剪切强度（psi）>2200（0.09“x 0.16”模具）

搭接剪切强度（psi）>2200

玻璃化转变温度，tg（℃）91

科夫。热的。实验温度低于tg（ppm/℃）75

高于tg（ppm/℃）233

离子含量

氯化物<10 ppm。

钠<10 ppm。

钾<10 ppm。

（典型特性不用作规范限值。）

建议的处理和固化：材料在收到后即可使用。存储冻结以保持*

流动特性。打开容器前，让材料预热至室温。使用前混合

如果包装在容器中，容器应重新悬挂填料。在150℃下固化60分钟，或在

175摄氏度。

贮存期：在25℃下保存<4天；在-10℃下保存6个月；在-40℃下保存12个月。

安全和操作：在通风良好的情况下使用。远离火花和明火。避免

长时间接触皮肤和吸入蒸汽。用肥皂和水清洗皮肤。

通过ISO 9001认证

创意材料公司

所有技术信息均基于CMI人员获得的数据，并被认为是可靠的。没有保证是

关于结果或可能侵犯的明示或暗示的。

修订日期：03/03/17修订日期：E

注射器操作指南

存储：

•收到货物后，应立即打开注射器的包装，并将其存放在-10°C的冰箱中。

不要将注射器保存在深度冷冻（-40°C）中。

•不要从包装主体处处理注射器。从包装的末端处理。

•垂直（直立）存放注射器，针头朝下。不要水平（侧面）存放注射器。

注射器应以这种方式储存，直到生产需要。注射器的保质期

在产品技术数据表上。

•注射器标有产品编号、批号和生产日期。重要的是

注射器按早生产日期“先出”使用。

准备使用注射器：

•要解冻注射器，请将其从冰箱中取出，注意不要接触注射器主体（手柄

从顶部和/或顶部），并允许他们适应环境温度与顶部向下。

•不要用手加热注射器。

•每个注射器的解冻时间将根据质量和成分而变化，但至少为45分钟

对于3cc、5cc和10cc，应至少观察90分钟，对于30cc注射器。

•不建议使用热源解冻注射器。

在融化过程中接近热源应大于3英尺。

•尽管大多数材料可以重新冷冻，但建议尽量减少冻融循环。

•一旦材料*解冻，移除保护性包装。

注射器信息：

•创新材料注射器配有Luer锁紧装置，与大多数配药类型兼容

设备。

•创新材料注射器采用光滑流动活塞技术设计，用于

自动或手动分配设备，但未配备手动柱塞。

•创意材料通常提供3cc、5cc、10cc和30cc体积的注射器。其他尺寸可能是

可根据要求提供。

122-39(SD)注射器用导热环氧模贴胶

 122-39(SD)
SYRINGE DISPENSABLE THERMALLY CONDUCTIVE EPOXY DIE ATTACH ADHESIVE
DESCRIPTION: 122-39(SD) is a syringe dispensable, thermally conductive, electrically insulating, one component,
100% solids epoxy adhesive. This system features excellent thermal stability, outstanding chemical resistance and
excellent high temperature properties. Applications include adhesion to gold plated substrates and tin/lead solder
terminated components, die attach and thermal management operations, printed circuit board fabrication, advanced
material composites, sealing and high performance coatings. 122-39(SD) is a thermally conductive version of 122-
38(SD).
PROPERTIES:
Viscosity (cps) 40,000
Thixotropic Index > 2.5
 Filler Aluminum Nitride
Percent Filler 60
 Volume Resistivity, max. (Ω-cm) 1 X 1016
Thermal Conductivity (W/mK) 3.5
Dielectric Constant (1KHz) 4.1
Dielectric Constant (1MHz) 3.9
Dissipation Factor (1KHz) 0.027
Dissipation Factor (1MHz) 0.038
Useful Temperature Range (°C) -55 to +250
 Thermal Stability (°C) Good to +300
Die Shear Strength (psi) > 2,200 (0.09” x 0.16” die)
 Lap Shear Strength (psi) > 2,200
Glass Transition Temperature, Tg (°C) 91
Coef. Of Therm. Exp. Below Tg (ppm/°C) 75
Above Tg (ppm/°C) 233
IONIC CONTENT
Chloride <10 ppm.
Sodium <10 ppm.
Potassium <10 ppm.
(Typical properties are not intended to be used as specification limits.)
SUGGESTED HANDLING AND CURING: Material is ready to use as received. Store frozen to maintain consistent
flow properties. Allow material to warm up to room temperature before opening container. Prior to using, mix
container well to re-suspend filler if packaged in containers. Cure for 60 minutes at 150°C, or for 30 minutes at
175°C.
STORAGE: Shelf Life: < 4 days at 25°C; or 6 months at –10°C; or 12 months at –40°C.
SAFETY AND HANDLING: Use with adequate ventilation. Keep away from sparks and open flames. Avoid
prolonged contact with skin and breathing of vapors. Wash with soap and water to remove from skin.
Creative Materials, Inc.
All technical information is based on data obtained by CMI personnel and is believed to be reliable. No warranty is
either expressed or implied with respect to results or possible infringements on patents.
 REVISION DATE: 03/03/17 REVISION: E
Guidelines for Handling of Syringes
STORAGE:
• Upon receipt of shipment, syringes should be unpacked immediately and stored in freezer at -10° C. Do
not store syringes in deep freeze (-40°C).
• Do not handle syringes from the body of the packaging. Handle from the ends of the packaging.
• Store syringes vertically (upright) with tip side down. Do not store syringes horizontally (sideways).
Syringes should be stored in this manner until needed for production. Shelf life of syringes will be indicated
on the products technical data sheet.
• Syringes are labeled with product number, lot number, and manufacturing date. It is important that the
syringes are used according to earliest manufacturing date, "FIFO” (first in, first out).
PREPARING SYRINGES FOR USE:
• To thaw syringes, remove them from the freezer taking care not to handle the body of the syringe (handle
from the top and/or the tip) and allow them to acclimate to ambient temperature with the tip down.
• Do not use hands to warm syringe.
• The thawing time for each syringe will vary based on mass and composition but a minimum of 45 minutes
for 3cc, 5cc, and 10cc and a minimum of 90 minutes for 30cc syringes should be observed.
• Using a heat source to thaw syringes is not advised.
• Proximity to a heat source during thawing should be greater than 3 feet.
• Although most materials can be refrozen minimizing freeze-thaw cycles is recommended.
• Once material is fully thawed remove protective wrapping.
SYRINGE INFORMATION:
• Creative Materials syringes have luer-lock fittings and are compatible with most types of dispensing
equipment.
• Creative Materials syringe are provided packaged with smooth flow piston technology design for use on
automated or manual dispense equipment but are not hand plunger equipped.
• Creative Materials routinely provides syringes in volumes of 3cc, 5cc, 10cc, and 30cc. Other sizes may be
available upon request.