118-02衬垫-可印刷，柔性，绝缘涂层

118-02衬垫-可印刷，柔性，绝缘涂层

说明：118-02是一种适用于移印的柔性电绝缘涂料。

喷雾、浸渍和注射器分配。本产品对卡普顿、聚酯薄膜、玻璃、塑料

以及其他各种表面。与传统绝缘材料不同，这种产品非常抗弯曲。

还有折痕。有些应用包括，但不限于，带状电缆，聚酰亚胺柔性。

电路，聚合物厚膜电路和薄膜开关。

典型固化特性：

粘度（cps）10000-12000

抗皱性佳

体积电阻率（Ω-cm）1.1 x 1014

介电强度（伏特/密耳）1300

损耗因子（100赫兹）0.013

介电常数（100赫兹）4.2

水汽透过率低

建议在使用前充分搅拌和固化。118-02已准备好用于喷涂

和/或浸涂。可通过添加CMI 114-20（缓慢干燥）或113来实现额外的稀释-

39（快干）稀释剂。当在130℃下固化5分钟时，大多数应用的性能良好。良好

通过在25°C到175°C的温度范围内固化，也可在各种基底上获得性能。

注：使用低温固化剂时，应加入1PHR B-187催化剂。建议使用B-187

高度耐化学性。建议终用户通过实验确定温度和时间

适合个人应用。

贮存期：25℃下保存3个月；5℃下保存6个月，-10℃下保存12个月

安全和操作：在通风良好的情况下使用。远离火花和明火。避免

长时间接触皮肤和吸入蒸汽。用肥皂和水清洗皮肤。保留

容器关闭以避免污染。如果冷冻储存，允许容器加热至室温，以及

打开前*擦掉所有冷凝水。

118-02衬垫-可印刷，柔性，绝缘涂层

 118-02
PAD- PRINTABLE, FLEXIBLE, DIELECTRIC COATING
DESCRIPTION: 118-02 is a flexible, electrically insulating coating suitable for application by pad printing,
spraying, dipping and syringe dispensing. This product features excellent adhesion to Kapton, Mylar, glass,
and a variety of other surfaces. Unlike conventional insulating materials, this product is very resistant to flexing
and creasing. Some applications for 118-02 include, but are not limited to, ribbon cables, polyimide flexible
circuits, polymer thick film circuitry, and membrane switches.
TYPICAL CURED PROPERTIES:
 Viscosity (cps) 10,000 - 12,000
Crease Resistance Excellent
 Volume Resistivity (Ω-cm) 1.1 x 1014
 Dielectric Strength (volts/ mil) 1300
Dissipation Factor (100 Hz) 0.013
Dielectric Constant (100 Hz) 4.2
Moisture Vapor Transmission Low
SUGGESTED HANDLING & CURING Stir well before using. 118-02 is ready to use as supplied for spray
and/or dip coating. Additional thinning may be accomplished by adding CMI #114-20(slow drying), or#113-
39(fast drying) thinner. Good properties for most applications result when cured of 5 minutes at 130°C. Good
properties are also obtained on a variety of substrates by curing at temperatures ranging from 25°C to 175°C.
NOTE: Add 1phr B-187 catalyst when using low temperature cures. The use of B-187 is suggested to impart a
high degree of chemical resistance. End user is advised to experimentally determine temperature and time
best suited for individual applications.
STORAGE: Shelf Life: 3 months at 25°C; or 6 months at5°C: or 12 months at -10°C
SAFETY & HANDLING: Use with adequate ventilation. Keep away from sparks and open flames. Avoid
prolonged contact with skin and breathing of vapors. Wash with soap and water to remove from skin. Keep
containers closed to avoid contamination. If stored frozen allow containers to warm to room temperature, and
thoroughly wipe off any condensation before opening.