绝缘电压击穿强度测试仪试验方式：
击穿试验、耐压试验、阶梯试验
绝缘电压击穿强度测试仪显示方式：
曲线/数据显示，数据打印。
试验空间：
绝缘油/空气
升压速率：
0.1KV/S-3KV/S
整机精度：
≤2%
技术指标：
输入电压： 交流 220 V 输出电压： 交流 0--100 KV ;
直流 0—100 KV 电器容量： 10KVA 高压分级： 0-100KV
升压速率：0.01-5.0kv （备注：满足标准要求并可以根据用户需求设定不同的升压速率）
试验方式：直流试验：1、匀速升压 2、梯度升压 3、耐压试验
交流试验：1、匀速升压 2、梯度升压 3、耐压试验
试验介质：空气，试验油 安装灵敏度较高的过电流保护装置保证试样击穿时在0.05S内切断电源。 仪器配备*故障报警系统 避免用户操作故障仪器发生危险。（上位机报警和下位机报警）
整机组成：
1、升压部件：2、动部件/3、检测部件/4、计算机软件/5、试验电极：
/1、由调压器和高压变压器组成0～50KV的升压部分。
2、由步进电机均匀调节调压器使加给高压变压器的电压变化。
3、由集成电路组成的测量电路。通过信号线把检测的模拟信号和开关信号传给计算机。
4、通过智能电路把由检测设备采集的测控信号传给计算机。计算机根据采集的信息控制设备运行并处理试验结果。
5、根据国家标准(1408.1-2006)随设备提供三个电极，具体规格为：Ф25mm×25mm两个；Ф75mm×25mm一个。
适用材料：
主要适用于固体绝缘材料如下：
电线套管、
树脂和胶、
浸渍纤维制品、
云母及其制品、
塑料薄膜、
陶瓷、
玻璃、
绝缘漆、
硫化橡胶、
电缆纸、
绝缘漆漆膜、
硬质橡胶、
纸板等
绝缘介质在空气或液体介质中，测量工频（48~62Hz）或对应直流电压下击穿强度和耐电压时间。
适用于连续均匀升压或逐级升压的方式，对试样施加交流/或直流，电压直至击穿，测量击穿电压值，计算试样的击穿强度；用迅速升压的方法，将电压升到规定值，保持一定的时间试样不击穿，定此时规定值为试样的耐电压值。
Test method:
Breakdown test, compression test, step test
Display mode:
Curve/data display, data printing.
Test space:
Insulating oil/air
Pressure rise rate:
0.1 KV/S - 3 KV/S
High precision:
2% or less
Technical indicators:
The input voltage: ac 220 V output voltage: communication 0-100 KV;
Dc 0-100 KV electric capacity: 10 kva high-pressure sizing: 0-100 KV
Pressure rise rate: 0.01 to 5.0 kv (note: meet the standard requirements and can be set according to user requirements different pressure rise rate)
Test method: dc test: 1, 2, gradient booster 3 uniform booster, withstand voltage test
Communication test: 1, 2, gradient booster 3 uniform booster, withstand voltage test
Test medium: air, oil test installation high sensitivity of over current protection device to ensure the sample breakdown within 0.05 S when cut off power supply. The instrument is equipped with advanced fault alarm system Avoid user operation fault instrument. Alarm (the upper machine and lower machine alarm)
The whole machine:
1, booster parts: 2, moving parts / 3, test parts / 4, computer software / 5, test electrode:
/ 1, consists of a voltage regulator and the high voltage transformer 0 ~ 50 kv booster section.
2, evenly regulating voltage regulator by stepper motor to high voltage transformer voltage change.
3, measuring circuit composed of integrated circuit. Through the analog signal and the detection line switch signal to the computer.
4, through inligent circuit by testing equipment acquisition of measurement and control signals to the computer. Computer control equipment operation according to the collected information and process the test results.
5, according to the national standard (1408.1-2006) with the equipment to provide three electrodes, specifications are: Ф two 25 mm x 25 mm; Ф a 75 mm x 25 mm.
Applicable materials:
Mainly suitable for solid insulating material is as follows:
The wire casing,
Resin and rubber,
Impregnated fiber products,
Mica and its products,
Plastic film,
Ceramics,
Glass,
Insulating paint,
Vulcanized rubber,
Cable paper,
Insulating varnish film,
Hard rubber,
Cardboard etc.
Insulating medium in air or liquid medium, the measurement of power frequency (48 ~ 62 hz) or the corresponding breakdown strength under dc voltage and voltage withstand time.
Apply continuous uniform booster or booster way, step by step toward a sample dc, ac/or until the breakdown voltage, breakdown voltage measurement, calculation of sample breakdown strength; Use the method of rapid booster, e., will increase the voltage to maintain a certain amount of time the sample breakdown, not set the withstand voltage value of the specified value for sample and now.
