传动轴扭疲试验机
- 公司名称 上海恒德科技有限公司
- 品牌 DZ/大中
- 型号
- 产地 德国
- 厂商性质 代理商
- 更新时间 2018/9/6 14:15:35
- 访问次数 795
联系我们时请说明是化工仪器网上看到的信息,谢谢!
产地类别 | 进口 | 价格区间 | 面议 |
---|
Measure fatigue limit and instantaneous strength(PV5802, PV5804)
1、手动装上传动轴整轴进行疲劳强度测试,手动卸下整轴。
Install the driveshaft manually, proceed the test, uninstall the driveshaft manually
测量疲劳极限和耐久极限。
Measure fatigue limit and endurance limit
轴温度超过60度将进行冷却,由载荷决定试验终止,通过频率下降或转角增加终止试验。
Cooling is needed when temperature of driveshaft is over 60?C, judging by frequency dropping or rotating angle increasing to end the test.
试验载荷按图纸要求。
Test load according to the requirement on the drawing
*1.4、可以测量瞬时强度,震荡频率为0.3HZ.
Measure instantaneous strength, vibration frequency is 0.3Hz
*1.5、自动记录断裂前的循环次数。
Automatically record test cycles before the driveshaft broken
整轴强度试验(TL82248):
Driveshaft assembly strength test(TL82248)
静态测试:
Static test
2.1手动装上传动轴整轴进行整轴强度测试,手动卸下整轴
Install the driveshaft manually, proceed the test, uninstall the driveshaft manually
*2.2静态测试MF和MV,力矩按图纸要求。
Static test of MF and MV, torque according to requirement on the drawing
2.3移动端倾斜角10度,固定端倾斜角40度下进行试验。
10? angle of inclination at moving end, 40? angle of inclination at fixing end during testing
*2.4应自动记录扭矩和转角曲线。
Automatically record torque-rotating angle curve
3动态测试
Dynamic test
*3.1力矩MT按图纸要求。
Torque MT according to requirement on the drawing
3.2移动端倾斜角7度,固定端倾斜角7度。
7? angle of inclination at moving end, 7? angle of inclination at fixing end during testing
*3.3 频率0-10HZ.
Frequency of 0~10Hz
*3.4 两端摆角范围±50度。
Swing angle range of both ends: ±50?
*3.5扭矩范围±8000NM;测量精度±1%。
Torque range: ±8000Nm with ±1% accuracy.
*3.6对应2HZ,±45度摆角;对应5HZ,±15度摆角
±45? swing angle according to 2Hz frequency, ±15? swing angle according to 5Hz frequency
4、操作手册、使用说明书、维修、保养说明书、电器、机械结构原理图、易损件清单、夹具图、故障排查清单,各种件的加工程序(磁盘,可在PC机上编辑)
Operation manual, maintenance manual, electrical and mechanical drawings, spare parts list, fixture drawings, trouble shooting list and software.
5、以验收8 05 98 39 004和8 06 97 29 023/8 06 98 29 024为主。测试台大小应能测量8 58 97 29 061。
Test stand should be big enough for Part 8 58 97 29 061, use Part 8 05 98 39 004 and Part 8 06 97 29 023/8 06 98 29 024 for pre-acceptance and finial acceptance test.
*6、具有自动反馈和记录功能。两端应有可换夹具进行测试不同整轴
Auto feedback and record function. Different fixtures for different driveshaft assemblies
*7、法兰盘端面距离应在300-1000范围内;
Distance between two end flanges: 300~1000mm
8、移动滑台采用自动方式(单独报价)。
Automatic slip table (quote as optional)
*9、VL节zui大外径为130MM,钟形壳zui大长度260MM。
Maximum diameter of VL shaft end: 130mm, maximum length of campaniform shell: 260mm
*10、屏幕上输入程序,可自动记录并打印出结果。
Data recording and result printing according to the program inputted.